BBV Tx1000 Guía de instalación

TX1000 Telemetry Transmitter Building Block Video Ltd 17 Apex Park Diplocks Industrial Estate Hailsham, East Sussex, BN27 3JU, UK Tel: + 44 (0) 13

TX1000 Manual V8 September 2013 10 Disabling/Enabling the program key. To enable/disable the programming key, press and hold the focus far and

TX1000 Manual V8 September 2013 11 Camera Selection A camera may be selected onto the controlled monitor by pressing the number(s) of the camera

TX1000 Manual V8 September 2013 12 This will add/remove the camera from the Sequence. Setting the Sequence delay Determine the delay you wish to

TX1000 Manual V8 September 2013 13 Keypad functions The keypads should not be connected or disconnected from a "live" working unit, a

TX1000 Manual V8 September 2013 14 Autopan – Press and autopan motor starts. Pressing Left or Right stops Autopan. Illuminated red when active

TX1000 Manual V8 September 2013 15 Maximum Camera Number To set the Maximum camera number, Press , then enter 15 and then the camera button follo

TX1000 Manual V8 September 2013 16 Patrol settings There are two preset patrols that can be started by the Tx1000. To activate: Press either

TX1000 Manual V8 September 2013 17 Setting a delay for Patrol 1: Delay NumberThenMenu OptionPROGRAM Setting a delay for Patrol 2: Delay NumberT

TX1000 Manual V8 September 2013 18 RS422 TELEMETRY The Tx1000 matrix has a single RJ45 connector that is used to control BBV RS422 telemetry rec

TX1000 Manual V8 September 2013 19 Tx1000 Series Alarm Input Option Alarm Inputs Alarms activate on opening of contacts. Connect each alarm pa

TX1000 Manual V8 September 2013 2 Contents Important – Before you install 3 TX1000 Telemetry Transmitter – an Introduction 4 Unpacking 5

TX1000 Manual V8 September 2013 20 Enabling/Disabling the Alarm package The alarm package can be enabled/disabled; for example at night when the

TX1000 Manual V8 September 2013 21 The length of time the contacts close is also programmable. To program the length of time the contacts cl

TX1000 Manual V8 September 2013 22 Self Test on the Keypad The keypad supports a self test for in the field testing. This will enable the servi

TX1000 Manual V8 September 2013 23 Tx1000 Alarm Program Table Site Name Date PROGRAM 11 INPUT NUMBER CAMERA NUMBER PRE

TX1000 Manual V8 September 2013 24 PROGRAM 11 15 PROGRAM 11 16

TX1000 Manual V8 September 2013 25 Extend your BBV Warranty from 12 months to 3 years As of the 1st September 2008 BBV have offered our custo

TX1000 Manual V8 September 2013 3 TX1000 Alarm program table 23 IMPORTANT Before you install: Please read the following points before servic

TX1000 Manual V8 September 2013 4 Tx1000 Telemetry Transmitter – Introduction The Tx1000 is a simple to use telemetry transmitter for multi-cam

TX1000 Manual V8 September 2013 5 Unpacking Inspect the packaging for signs of damage. If damage has occurred, advise the carriers and/or the

TX1000 Manual V8 September 2013 6 Rx10Xdome cameraSTATICstatic cameraRX200Static camera withlights/wash/wipeRX200Simple AC pannerRX300AC P/T Zoo

TX1000 Manual V8 September 2013 7 Technical Specification Power supply 12V dc 500mA Inputs Data input to base unit is RS232 via 9-pin D connec

TX1000 Manual V8 September 2013 8 Layout of the Tx1000 keypad 12Vdc Video In Video Out Installing the Tx1000 Matrix & Keypad 1. Mount t

TX1000 Manual V8 September 2013 9 Status LED The STATUS LED should flash and the monitors should show the video from Camera 1 on power up. If t